Are you all right in entering and leaving the water?

No matter what kind of style, put on equipment to stand up and need to spend some effort, weight and weight of the gas cylinder is not light, at least more than 15 kilograms, plus wear winter clothes, not in the water before they should not move Far distance, especially reef seashore, to avoid danger or heat stroke. The fins should be portable before the shore is potentially in the water. In general, the shore dive and the boat dive are very different. Although beginners began to learn from the shore dive, but soon after the ship dive is very likely, if you go to Southeast Asia and other places, especially overseas dive sites .

However, if you do not sink immediately after entering the water, it will be easier for the backstroke to face the sky with the backstroke, because the cylinder has weight. But the downside is that you can't see the front. You should look up at each direction after kicking the fins for a certain distance. Or are there obstacles such as reefs? In addition, before entering the water, the location of the water point should be kept in mind, and the azimuth angle should be confirmed with the northbound target's point of entry or significant target in order to facilitate the return landing.

Hiking into the water

Divebari gentle coastal terrain as long as the dress is complete, holding the frog slowly into the water, when the water depth and waist depth, then put the frog shoes. Diving activities must strictly abide by the system of snorkeling, so when the fins are worn, the two can help each other. The person wearing the fins will put one hand on the diving partner and raise one leg across the other knee to form a “4” shape. , and then put on flippers and then change to another, the other person is the same. In addition, you can also wear the mask, bite the secondary mouthpiece after the mouth, the BC will be inflated to half full, to determine the normal inspiration and exhalation, directly under the squat did not enter the water to wear flippers, and then swim out to the surface.

This method is suitable for long shoals or sandy shore terrain. Sometimes it takes a long distance to walk in water to reach enough depth to swim in front of a flipper. As long as you can swim, lying on the surface of the water to kick fins is much easier to walk than walking on the sea floor. It is safer because reef rocks are uneven and it is difficult to walk a few steps.

Step into the water

Scuba-Entry-Methods-Giant-Stride-Entry step into the water is to directly enter the water in a large step after the equipment is dressed. It is applicable to the situation where the tide falls within one meter. The boat dive or the reef subsurface terrain Can be used. Before standing in the water, stand on the water's edge. When the boat is latent, pay attention to whether or not there are handrails to assist standing balance. Before entering the water, make sure that there is no water on the surface, the depth of the bottom of the water or the depth of the water is deep enough to avoid impact injuries.

Before entering the water, BC should be inflated at least to a half-full state. After wearing the top mirror, bite the secondary head to maintain inhalation, and then hold the secondary head with the palm of your right hand while pressing your finger against the mirror (the purpose is to prevent the impact of the water from dropping off the mirror). Then, the left hand holds the three-meter table and drags around the waist. Standing in this position and standing by the waterside, striding out to the surface of the water, his feet naturally fall into the water with scissors, and when he enters the water, his legs are clamped and the body naturally rises upwards.

Roll back into the water

Backs-roll is often used this way when boarding a boat for a dive. After the dress is finished, the right hand holds the secondary head and the mirror, and all the regulator's pipe table groups should be hung on the chest as far as possible so as not to hook up the obstacles and cause equipment damage and danger when rolling back into the water. After inflating the BC, it was confirmed that the secondary head was breathing properly, and then he covered his hindbrain with his wrist. The body sat on the side of the ship and the body fell back into the water with his back in the water first.

Water way

The potential of entering the water on the shore should be taken into consideration when the waves are higher, but whether to return to the shore is not. The most appropriate method should be adopted depending on the terrain.

Water conditions in the water layer are relatively stable, but the closer you get to the water surface, the more you can feel the waves turning. When the return end of the dive is close to the shore and has not yet surfaced, if you feel that the body is being driven by the waves, the sights are white. The bubble indicates that it is trapped in a reef area. At this time do not rush to surface, so as not to be hit by the waves hit the reef injured. At this point, we must turn back and dive back to deeper areas where there is no deep spray, and then emerge from the water to observe more easily landed terrain. The bigger the waves are, the more difficult it is to return to the shore, and the frog shoes must be removed before going ashore. However, the second-level head should continue to bite and keep breathing. When the waves are small, they quickly climb to the shore. Therefore, you should be accustomed to wearing flippers in the water, and you can't move too slowly, so as not to be pushed ashore by the waves.

If you visit a shipwreck dive site, it is best to go up along the anchor line, grab the anchor line to make a decompression stop, and then slowly rise. This way of expulsion is the best way to ship the dive site because your dive boat will usually Parked near the anchor rope waiting for the diver to discharge water.

1. Environmentally friendly and degradable : The main material of paper Bento Box comes from renewable resources - wood. Compared with plastic or other synthetic materials, paper bento boxes are easier to decompose naturally after waste, reducing pollution to the environment.

2. Food safety : high-quality paper bento boxes are certified by food safety standards, and the inner layer is usually food-grade coating to ensure that the food will not react adversely with the packaging materials during storage and carrying, ensuring the hygiene and safety of the food.

3. Light and easy to carry : Paper bento box is light in texture and easy to carry. Whether it is work, school or outdoor activities, paper bento boxes can easily meet the needs of carrying food.

4. Beautiful customization : Paper bento boxes can be customized according to different needs and occasions, such as printing corporate LOGO, pattern or text, which not only increases the beauty of the product, but also helps brand publicity and promotion.

5. *Easy to recycle : The paper bento box can be easily put into the recycling station after waste, and can be reused after recycling treatment, reducing the consumption of natural resources.