Six tips to teach you to buy quality wardrobes

[ Chinese wardrobe net ] The home is to be renovated, wardrobes , bookcases, etc. are essential furniture. And when you are in a market with a lot of brands, how to buy a wardrobe? Because you are worried about environmental protection, quality, function, service, etc., you may have been wandering around the wardrobe market for a long time, but hesitated because of each one. I don’t know how to decide; maybe I haven’t strolled before, and I’m more anxious to buy what I can buy in my own cabinet, because I have no experience. Don't worry, choose a wardrobe for you.

wardrobe

As the saying goes, I am not afraid of not knowing the goods and I am afraid of the goods. You can ask from these aspects to understand the comparison and then decide:

The first trick: kanban cutting edge and edge banding.

Many people may neglect to look at the overall surface. It is not cheap to look at. It is not cheap to look at it. In fact, the neat and beautiful edge of the board after cutting is related to the two aspects of the sawing environment of the sheet itself. First, the density of the core must be uniform, otherwise When cutting at the same speed, the cutting is easy to collapse when cutting to a place where the density is not uniform. The poor process on the market directly sees the chipping. If you want to pick a good process, it is obvious after the naked eye. Bumping, but also touch by hand, the edge of the board is fine and uniform. First, the density of the board itself must be uniform. (Note: The material with uneven distribution density is prone to deformation during use). The second is to indicate that the factory is replacing the saw blade. Management is in place, usually the manufacturer behind the equipment or in the form of private plus workshops may change the saw blade once a day or even a few days. The result is that the jagged edges are not only unsightly, but the most important thing is to influence the edge as much as possible. Every point of the zero contact contact adhesion, in the end, especially the city of Shenzhen itself is relatively humid by the sea, the humid air will hollow out, slow

The second measure: Kanban.

At present, various brands in the market are mostly made of MDF because of their lower texture than MDF and poor nail holding power. MDF usually has a density of 450-880KG/M3, and density of 750KG/M3 or higher can be called high density medium fiber. Board, but high-density board is often used in laminate flooring, so some merchants want to make their products better in the quality of customers, they will say that their products are high-density boards, you can ask the marketing staff for their quality inspection report. Look, of course, some stores may sell a few brands, so don't be "Zhang Guan Li Dai", you must be seated. Generally, manufacturers with strength and sales are unwilling to sell their stores with many brands of products and their products are appearing in one exhibition hall at the same time, so it is best to go to a professional brand store to buy. The technically good quality material of the tripolyhydrogen ammonia veneer can be seen from the surface texture and the uniformity of the hand. Generally, the higher the texture and the better the feel, the better the quality of the tripoly hydrogen fluoride veneer. It is expressed in abrasion resistance and moisture resistance. The highest level of surface veneer color is 8 levels, the higher the level, the higher the resistance to discoloration.

The third measure: look at environmental protection.

European standards currently have E1 and E2 grades according to the amount of formaldehyde released on the market. The former is used indoors and the latter is used outdoors. The E1 level standard requirement is: ≤1.5MG/L. Excessive formaldehyde can cause chronic diseases such as the respiratory tract that seriously affect your health. (Some small brands also say E1, but it is the level after the edge is sealed. The good sheet substrate itself is E1.) The country has recently issued a more advanced certification: "10-ring certification", which can be used in the panel furniture industry. The environmental protection that is the first to pass some certification is more guaranteed.

The fourth measure: ask whether the plates and frames, tracks, wheels and other related items used by the brand are produced by the factory.

Generally, if you buy a board in another place and buy a hardware in addition to the inability to achieve a unified supporting effect, the key is to purchase and assemble it, it is possible to purchase one or more pieces, so the quality of the batch of items used for the purchase and assembly is It is difficult to balance the guarantee, which means that the buyer has to take chances. (Note: There are many manufacturers on the market to save the cost of the frame, the aluminum alloy used in the track is not the original aluminum, but the recycled aluminum, the sawing profile light measurement is darker than the original aluminum, the thickness may be thinner than 1.2mm, recycled aluminum It is easy to oxidize and has a short service life. The sliding door wheels pay attention to the hard texture and reasonable design, otherwise the pushing position is not smooth and easy to break, especially the wear resistance of the outer ring of the wheel and the flexibility of the shaft.)

The fifth measure: ask the number of manufacturers in China's specialty stores.

The market is maturing, and the brands with certain market support rate and good reputation have developed rapidly in the Chinese market for nearly ten years. There are many brand stores that can develop under fierce competition, but if the manufacturers have many points or even every region, Everyone has to pay attention: this kind of situation is often prone to profit for the purpose of distributors everywhere, in the choice of raw materials and production processes are very different, the final selling of the same brand and the products given to customers are not the same. The production area of ​​the manufacturer is also a ratio. The small-scale workshops are dozens of squares or hundreds of square meters, and the production line will be relatively backward.

Sixth trick: look at the service. Mainly reflected in the following aspects:

1. The process of customizing the closet cabinet or sliding door must be confirmed - that is, confirm the drawing. The professional service brand has certain opinions and principles in various suggestions or opinions. It will not be done because of your needs, but according to your needs, the design, suggestions or opinions will be given reasonably in the comprehensive process of the factory and the product. Service personnel with higher brand requirements generally draw by hand and computer graphics, because only in this way can bring more deeper things to customers, so feel at ease.

2, product warranty. Professional brands will issue regular quality warranty cards and instructions for use. The instruction manual will explain the scope of application, the implementation standards, the quality level, the materials used, the installation, the adjustment, the use and maintenance, etc. The low-quality brands do not know these, so they cannot tell the consumers.

Traditional! Modern! Contemporary! Learn more about our dressers and chests for Bedroom Furniture.


Chests-These narrow bedroom storage pieces are great for storing shirts, pajamas, socks and more. Our bedroom chests feature three to six drawers.

Dressers-Dressers are often wider than chests. They also tend to have more drawers than chests, making them a great piece of furniture when you need additional storage for your bedroom.

wooden chest bedroom furniture Walnut-Wooden-Storage-Dressing-Stand-Table-Wooden-Furniture(6)


Chests&Dressers

Dressing Table,Oak Dresser Stool,Vintage Wooden Chest,Wooden Bedroom Furniture Chest

Changzhou Junhua Furniture CO.,LTD , https://www.blackstone-furniture.com

Posted on