1 , solid wood board, as the name suggests, solid wood board is a wooden board made of complete wood. These plates are sturdy and durable, and the texture is natural. However, due to the high cost of such panels and the high construction process requirements, there are not many uses in the decoration. Solid wood boards are generally classified according to the physical name of the board, and there is no uniform standard specification. At present, in addition to the use of solid wood panels for floors and door fans, the panels we use are generally artificially machined panels.
2 , splint, also known as plywood, commonly known as fine core board. It is made of three or more layers of one millimeter thick veneer or sheet adhesive. It is the most commonly used material for hand-made furniture. The splint is generally divided into three sizes of 3 PCT, 5 PCT, 9 PCT, 12 PCT, 15 PCT and 18 PCT (1 cm is 1 cm) .
3 , decorative panel, commonly known as the panel, is a solid wood plate precision cut into a thickness of about 0.2cm of thin veneer, with the plywood as the substrate, through the adhesive process made of single-sided decorative decorative sheet. It is a special way of splinting and has a thickness of 3 centimeters.
4 , blockboard, commonly known as large core board. The large core board is made up of two sheets of veneers bonded together in the middle. Daixinban cheaper price than the thin core plates, the flexural strength of the pressure difference, the vertical (to distinguish the core material), but the lateral bending strength of higher pressure.
5 , particle board, particle board is the use of wood scrap as the main raw material, then infiltrated with glue, the additive is pressed into a thin sheet. According to the pressing method, it can be divided into two types: extruded particle board and flat particle board. The main advantage of this type of sheet is that it is extremely cheap. The disadvantages are also obvious: the strength is extremely poor. It is generally not suitable for making larger or mechanically demanding furniture.
6 , MDF, also known as fiberboard. It is made of wood fiber or other plant fiber, and the artificial board made of urea-formaldehyde resin or other suitable adhesive is divided into high-density board, medium-density board and low-density board according to its density. MDF is also easy to rework due to its soft and impact resistant properties. In foreign countries, MDF is a good material for making furniture, but because the national standards for height plates are several times lower than international standards, the quality of MDF use in China needs to be improved.
7. Fireproof board and fireproof board are decorative boards made of silicon material or calcium material as the main raw material, mixed with a certain proportion of fiber materials, lightweight aggregates, adhesives and chemical additives. It is a new type of material that is being used more and more, and its use is not only due to fire prevention. The construction of fireproof board has higher requirements for sticking glue, and the price of fireproof board with better quality is more expensive than decorative panel. The thickness of the fireproof board is generally 0.8mm , 1mm and 1.2mm .
8 , melamine board, the full name is melamine impregnated film paper veneer wood-based panel, is a wall decoration material. The manufacturing process is to put paper with different colors or textures into a melamine resin adhesive, and then dry to a certain degree of solidification, and lay it on the surface of particleboard, medium density fiberboard or hard fiberboard, and hot pressed. Decorative plates.
9 , broken wood, broken wood is made of wood processing corners as a residual material, chopped, dried, glued, hot pressed.
10 , wood board, also known as Wanli board, is the use of wood scraps, through the machine to plan the wood, through the chemical solution of the soak, and then blended with cement, into the molding pressure, solidification, drying.
11 ã€Plywood, plywood is made of three or more veneers, which are divided into two kinds: broad-leaved tree rubber plywood and coniferous wood plywood.
12 , the fir integrated board is that each layer is made up of a plurality of longitudinally continuous fir strips, the facing board and the bottom board are longitudinally arranged structure, the middle layer board is a horizontal arrangement structure, and the integrated board is a three-layer type. Introduction to the integrated board: 1 . It is made of short solid wooden blocks , which are processed by the process of opening teeth and E0 grade environmentally friendly adhesive. 2 . The integrated board retains the natural wood texture, beautiful appearance and good environmental performance. 3 . The raw materials of the laminated timber are fully dried, and even in the large-section and long-sized materials, the moisture content of each part is uniform, and the cracking and deformation are small compared with the solid wood. 4 . Can be widely used in high-end home decoration, as well as office, hotel, entertainment and other high-end business venues.
13. Wood-based panels and artificial panels are made of natural wood chips, hibiscus and shavings. The advantages of the wood-based panel are: large format, good structure, convenient construction; low expansion and contraction rate, stable size, uniform material compared with sawn timber, and not easy to deform and crack; the veneer and various scraps used as raw materials for artificial board are easy to be impregnated , thus Can be used for various functional treatments ( such as flame retardant, anti-corrosion, anti-shrinkage, wear resistance, etc.); a wide range of thickness and density grades are highly applicable; bending forming performance is better than sawn timber. The disadvantage of the wood-based panel is that the rubber layer will age , the long-term bearing capacity is poor , the service life is much shorter than the sawing material, and the bending and tensile strength are second to the sawn timber. However, due to the lack of wood, wood-based panels have been used to replace many traditional uses of sawn timber, and their production has increased rapidly.
14 , ecological board , also known as melamine sticker board, the full name is melamine impregnated film paper veneer wood-based panel. Paper with different colors or textures is soaked in eco-resin resin adhesive, and then dried to a certain degree of curing, paved on particleboard, moisture-proof board, medium density fiberboard, plywood, blockboard or other hardboard. Surface, hot pressed decorative panel. In the production process, it is generally composed of several layers of paper, and the quantity depends on the purpose.
15 〠Rabbit paint plate, paint-free decorative material has natural texture, clear wood grain, can be compared with logs, the world's currently popular wood species, and the surface of the product has no color difference, self-extinguishing from the fire, washable, wear-resistant, Moisture-proof, anti-corrosion, anti-acid, anti-alkali, non-stick dust, no mold and blackness caused by the moisture of the wall, product design and production, reasonable color matching, easy construction, good sawing, never rupture, repair Trimming uses the paint-free line to match, glue with glue does not need to worry about the ash after nailing, and does not need to paint, can save the labor and paint cost of the paint after construction, avoiding the paint producing unhealthy smell and carcinogenic substances to the human body, not only It saves the cost of long-term maintenance and care, and shortens the construction time. The effect is both elegant and the cost is reduced. Therefore, it is a new generation of paint-free decorative materials that are green, non-toxic, tasteless and pollution-free. The products are high-grade and affordable. Leading the new trend of decorative materials.
16 ã€Tooth plate, the tooth plate is made of multiple pieces of wood strips in the longitudinal direction and the transverse direction, and is cold-pressed and spliced, that is, the integrated board. The specific process summary is: wood strips of the same width, thickness, and the same length or different lengths. The two ends of the length direction are respectively serrated by special woodworking equipment, and the white teeth of the two adjacent wood strip ends are coated with white latex. , inserting into each other, called the tooth joint. Since the serrated interface is similar to the finger cross docking, it is also called the finger joint.
Accessories Of Airless Paint Sprayer
The sprayer can basically be divided into the following parts:
Gun, tip, Motor & Drive System, pump assembly, filter, Pressure Control, auxiliary spray accessories.
Gun
• Acts as the on/off valve for the material Spray Tip
• Controls the amount of fluid sprayed by using different orifice sizes
• Orifice shape determines the spray pattern.
• Many Graco tips can be turned to the reverse position by hand to blow out clogs
Motor & Drive System
• A heavy duty system that drives the pump
Pump
• Also called the Fluid Section
• Delivers a steady stream of high pressure fluid through the hose to the spray gun filter,
• Prevent large particles from entering and avoid clogging the spray gun
Pressure Control
• Used to regulate the fluid pressure delivered from the pump
Accessories Of Airless Paint Sprayer,Airless Paint Sprayer Tips,High Pressure Paint Sprayer,Paint Sprayer Rental
Fuzhou HVBAN Mechanical Equipment Co., Ltd. , https://www.hi-sprayer.com